汽车制动试验台检测系统设计

作者：梁奇1，李晶2 日期：2008-11-03/span> 浏览：3965 查看PDF文档

汽车制动试验台检测系统设计

梁奇1，李晶2
（1.杭州电子科技大学 智能控制与机器人研究所，浙江 杭州 310018； 2.无锡博世柴油系统股份有限公司，江苏 无锡 214000）

摘要：为了实现汽车制动试验台所需的检测控制系统，根据制动试验台自身的机械结构进行了相应的设计。该检测系统由数据采集、数据处理和数据输出三大部分组成，系统通过这三部分来采集试验台的检测数据，控制试验台的运行，并把试验数据传送到上位机加以分析。采用了固态继电器、单片机和ADC0809芯片，作为必要器件来控制和设计电机、上下位机的通信以及A/D信号的转换。实验结果表明，该设计能够满足系统检测数据的要求，并具有试验可接受的精度。
关键词：制动试验；检测；数据采集；汽车；单片机；固态继电器
中图分类号：TP274文献标识码：A文章编号：1001-4551(2008)10-0014-04

Design for detection system of automobile brake tester
LIANG Qi1, LI Jing2
(1. Laboratory of Intelligent Control and Robot, Hangzhou Dianzi University, Hangzhou 310018, China;
2. Wuxi Bosch Automotive Diesel Systems Co.Ltd., Wuxi 214000, China)
Abstract: For realizing the required detection system of test bench, the design of the system was given based on the mechanical structure. The entire detection system was consists of data acquisition, data processing and data output. With these three functions, the inspection data was collected, the operation of test bench was controlled and the test data was sent to host computer for analysis. The system was improved for the control of motor, the design of communications between upper and lower computers, and the transformation of A/D signals, by using solid state relay(SSR), microcomputer control units(MCU) and chip ADC0809. The test shows that design meets the demand of detection system with acceptable precision.
Key words: brake tester; detection; data acquisition; microcomputer control units(MCU); solid state relay(SSR)
参考文献(References):
［1］高红红,李平,劳奇成，等.汽车制动性能检测系统的设计与分析［J］.西安工业大学学报,2006,26(5):435-438.
［2］GANESH D, ARUNACHALAM V. Onroad brake testing［J］. Evaluation Engineering,2001,40(11):30-32.
［3］DERATO F C. Automotive Electrical and Electronic Systems［M］. Columbus: McGrawHill,1994：10-25.
［4］陈梓城.实用电子电路设计与调试［M］.北京:中国电力出版社,2006：114-134.
［5］WIESER R S, LECHNER A. Dynamic brake test stands［J］. IEEE Industry Applications Magazine,1998,4(6):35-40.
［6］求是科技.单片机典型模块设计实例导航［M］.北京:人民邮电出版社,2004：35-227.
［7］胡健.单片机原理及接口技术实践教程［M］.北京:机械工业出版社,2004：2-8.